A walk-in cooler can be an essential item in your home. You might be wondering How To Build A Walk In Cooler that is just for you. Imagine if you have a unique item that many people love.
Publican Anker is certain that it will be great. It not only saves money but also makes you stand out from others. Regrettably, you have skipped this tutorial. Follow the instructions at the end to learn how to build a walk in cooler create a unique A-walk-in cooler.
Where Should You Put Your Walk In Coolers?
The location of your walk in cooler is crucial if you are building one that will stand up to the elements. This is especially important if you live near a hot climate.
Your commercial cooler will be happier in direct sunlight, just as you are more comfortable in the shade during summer. This is crucial for energy savings. Direct sunlight cools coolers at 70% less than those in the shade.
To get the best performance, keep your cooler in a protected place.
- In an existing building
- Under a tree
- To the north of a barn
- An existing structure has an overhang.
You should make sure that your cooler has an open-vent roof if you have an overhang.
A small cooler with a flat roof may be structurally sound, but they are not designed to protect the sun. A standard peaked roof that has ventilation above the cooler ceiling can shade it and provide passive ventilation. This will help to keep the coolant circulating and save you money.
Notice: Heat rises. This is why we place twice the spray foam insulation on the roof of a house than the walls. Cold air sinks, so keep your own cooler roof from direct sunlight. You can still put spray foam insulation on the roof just like you did on the walls. This will help you save money on both construction costs and ongoing operating expenses.
How Much You’ll Save With a CoolBot-Powered Walk-In Cooler
CoolBot makes cold storage available for farms of any size. A traditional walk-in cooler costs between $6,000 to $10,000, depending on its size. You should also consider operating costs (energy and maintenance), which often require a trained technician.
CoolBot, on the other hand, is a more cost-effective solution and will save you money in the long term.
On average, our customers spend $3,000 to build their walk-in coolers.
All equipment and insulation are included in the $3,000 price. Many farmers reuse pressure treated lumber and insulation to save even more money. This allows them to build coolers for as little as $1,000.
The savings don’t end there. CoolBot uses approximately 40% less energy than traditional coolers, which means that you will continue to save money each month. You won’t even need to call a technician. To resolve any issues that may arise, our customer support team is available by phone or email.
NOTES
Available on Store It Cold climates: 18K BTU LG cold air conditioner
- Denver, Colorado quote for standard walk-in cooler refrigeration system installation
- A CoolBot-driven system is more efficient than a traditional refrigeration system to simulate a cooler, saving 41.7% on energy. The cool simulated cooler measured 250 square feet and was located in Albany. It was set at 41 degrees Fahrenheit. The NYSERDA report, page 13, discusses the evaluation of the CoolBot low-cost, walk-in cooler concept.
To build your walk-in cooler, you will need these three items:
- A well-insulated space
- An air conditioner
- CoolBot
- These three components are described in detail in the rest of this guide.
- How to make a homemade walk-in cooler
- Things You Will Need
- Wood planks 2 x 4.
- 3/4 inch plywood
- 2-inch board of polystyrene
- Particleboard
- Fiberglass insulation
- Vinyl flooring and vinyl wallboard
- 15 amp breaker
- Box with electrical outlet
- Cold air conditioner unit with a programmable thermostat
- Weatherstripping
- Liquid nails
- Staples
- Wood screws
- Wooden doors
- Warn!
When working with tools, always wear gloves, masks, or goggles. When working on your cooler, make sure that all electrical breakers have been turned off.
Ask for help from an expert if you don’t have any knowledge about electrical systems.
If you require more refrigeration space for perishable food, building a walk-in cooler can be useful. It can be very expensive to purchase a walk-in cooler or have one built for you. You can save money and time by building your own.
You will need to have the right tools and parts at your local hardware store, as well as a basic understanding of your electrical system. However, you can make a walk-in cooler for a fair price in your home with some effort and time.
You should choose a space in your home that is large and close to an electrical box. Because it uses a lot of electricity, its own walk-in cooler needs its breaker.
Your 2×4 wooden planks will be your frame. Make sure to leave enough space for your wooden doorway and air conditioner unit. Two inches should be allowed between the 2×4 planks. You will need 16 2×4 planks to make an 8x8x8 cooler. The same process applies to your ceiling frame.
For your flooring, use 1/4-inch plywood as the base. To cover the entire floor, you will need 64 square feet worth of particleboard. Once the frame is completed, you can install the door.
Your electrical wire should be run to a plug in the area you have created for your air conditioner unit.
A special circuit is not required, but the wire should be connected to the breaker installed for your DIY walk-in cooler. Any size unit can be used, but the minimum requirement is that it must have at least 18,000 BTUs to cool an 8x8x8 cooler.
Use wood screws to attach particle board to your ceiling and wall frames. Now your cooler should be fully enclosed. Use staples to attach fiberglass insulation between 2×4 planks on the ceiling, floor, and walls.
Lay your vinyl flooring, and then attach your insulation board to your ceiling and walls using liquid nails or glue. Attach the vinyl wallboard to your walls.
You will need to install the air conditioner unit in the opening you have cut in your frame. Then attach the cabling behind it to the breaker you had previously designated.
Screws should be provided to attach the unit to the wall. The thermostat should be set between 35 and 45 degrees Fahrenheit.
ADVANTAGES OF COOLBOT AND YOUR OWN WALK-IN COOLER
You can build your walk-in cooler from a garage or shop. You can also modify an existing cooler. A standard trailer can be used to make a portable cooler. This will allow you to preserve your harvest and enjoy the benefits of wild-game meat aging.
Cool Bot eliminates the need to worry about spoiling meat and fitting everything into a standard portable cooler. These are two major problems hunters face. Coolbot temperature controller is a great option for hunters all across the country, as it works in both hot and cold environments.
CoolBots are easy to use, which is what makes them so great. A properly insulated Cool Bot.
CoolBot’s simple controls allow you to set a temperature sensor in any room. The wire labeled “Room” measures the temperature sensor of the room. Let it hang free, but make sure it’s not making contact with any metal and is not in the direct pathway of the cold air coming from the A/C. Place the wire labeled “FIN Sensor” into the front cooling fins of the A/C window unit. Gently place the sensor as low as possible, but ABOVE the first horizontal cooling tube.
CoolBot provides many guides to help you build a well insulated room, trailer, or other space. CoolBot does the rest. If you already have a through-wall unit, don’t hesitate to use it. But if you’re purchasing a new A/C, you’d be better off with a window unit or a mini-split. Portable A/C – Not recommended Portable A/C air conditioning units bring too much warm air to the indoor cooler, and they can only get down to 50°F / 10°C. They’re also more expensive and consume more electricity than our recommended units.
Many hunters long to have building a walk-in cooler. CoolBot can help you make it a reality and allow you to hunt earlier, more often, and in warmer weather. The third wire (labeled “Heater”) attaches to the A/C’s temperature sensor. The temperature sensor actually comes out of the A/C; on a new A/C the temperature sensor will be mounted on small plastic brackets in front of the fins.
Relevant articles for you:
- How To Make A Swamp Cooler
- Make A Peltier Cooler 2023
- How To Make A Cooler Float
- How To Reduce Humidity In Air Cooler Top Full Guide 2023
- How To Make A Waterproof Cooler Radio
- What Size Cooler Do I Need
FAQs
How much does it cost to build a walk-in cooler?
On average, our customers spend $3,000 to build their walk-in coolers. All equipment and insulation are included in the $3,000 price tag. Many farmers reuse lumber and insulation to save even more money. This allows them to build coolers for as little as $1,000.
Can you use an air conditioner for a walk-in cooler?
A CoolBot and a window air conditioner can transform a well-insulated space into a walk-in cooler in just minutes.
Is a walk-in fridge worth it?
If your kitchen’s cold storage needs or production capacity exceeds the reach-ins capabilities, it’s worth considering a walk-in cooler. Own walk-in cooler can also greatly improve the efficiency and organization of your kitchen.
What size right air conditioner do I need with my CoolBot?
Our recommendation for an 8x8x8x8 room would be 12,000 BTU’s at 38degF. You could increase the size by up to 15,000 BTU or 18,000 BTU.
Conclusion
The self-built Walk cooler can be easily found through research. A DIY walk-in cooler can be a turning point that will allow you to express your creativity. Publican Anker has detailed all methods. We wish you success.
You can comment below if you have any questions. Publican Anker will monitor and filter all questions. Your comments are a great way to help the article become better.
